When an attic conversion needs steel beams
A converted attic in Ireland is treated as a new storey once it becomes living space. That brings in fire safety, stairs and structural rules, and often a steel beam or two. Here is what the official guidance says, and what an engineer and a fabricator each do.

Habitable room or storage?
The Department of Housing's Loft Conversion Guidelines (2022) explain that when the roof space of a house is converted to living accommodation, an additional storey is in effect added. A bungalow becomes a two-storey house and a two-storey house becomes a three-storey house, and the fire safety provisions go up accordingly.
A floored attic used only for storage is not the same as a bedroom or office. If you call it storage but use it as a room, it will not meet the rules for a habitable room, which can cause problems for safety, insurance and when you sell. Decide the use first and design for it.
Fire safety and escape (Part B)
The guidelines point to TGD B Volume 2 (Dwelling Houses, 2017) and its Appendix D. For a two-storey house, special provisions apply where the conversion does not raise the roof above the existing ridge, is 50 square metres or less, and has no more than two habitable rooms. In that case, the guidelines include:
- Enclose the existing stairs in 30-minute fire-resisting construction, leading to a final exit or to two escape routes at ground level.
- Fit 20-minute self-closing fire doors to habitable rooms off the protected stairway.
- Make the new attic floor and the existing first floor achieve modified 30-minute fire resistance (R30, REI 15).
- Give each new attic room a window or rooflight for escape or rescue: an unobstructed opening of at least 450 mm in each direction and 0.33 m², with the bottom of a rooflight opening at least 600 mm above the floor, and no more than 1700 mm from the eaves to the cill.
- Provide interconnected mains-powered smoke or heat alarms with battery back-up, or radio-interconnected alarms with 10-year sealed batteries.
Stairs (Part K)
The new stairs should follow TGD K (2014). For private stairs, Table 1 gives a maximum rise of 220 mm, a minimum going of 220 mm and a maximum pitch of 42 degrees. Headroom is generally at least 2 m; in a loft conversion where space is limited, it can be not less than 1.9 m at the centre of the stairs, reducing to 1.8 m at the side for a minor projection.
Alternating-tread and steep spiral stairs are not normally accepted, but TGD K says they may be considered in a loft conversion where there is not enough room for a normal stair, the stair serves accommodation used infrequently, and that accommodation has only one habitable room. A fixed ladder should not be the main access to a habitable room.
Structure (Part A) and ventilation (Part F)
Existing ceiling joists are rarely designed to carry a floor, and cutting roof trusses or purlins to make room changes how the roof is held up. The Loft Conversion Guidelines say professional advice should identify these structural issues. This is where steel beams often come in: to carry new floor joists, to replace a purlin or a cut truss, or to support a dormer opening. The engineer designs them to Part A and the Eurocodes. Part F (ventilation) and the other Parts of the Building Regulations also apply to the new rooms.
Planning: dormers and rooflights
The house exemptions in Schedule 2 of the Planning and Development Regulations 2001 cover extensions to the rear (Class 1) and sheds and similar structures (Class 3). There is no class in that schedule for dormer windows. If a dormer changes the outside of the house, check with your local planning authority whether you need permission; many do.
The Loft Conversion Guidelines also say that if the house is a protected structure, or a proposed one, you may need planning permission for the conversion itself, and you should contact the council's Conservation Officer early.
When an engineer must design the steel
Any beam that holds up part of the house, such as a new floor, a roof, or a wall above, should be designed by a chartered or competent structural engineer, with calculations. The engineer specifies the section size, the bearings and padstones, the connections and any fire protection. A fabricator should not guess a size, and neither should a builder.
What to have ready
- Your engineer's drawings and steel schedule, or the name of your engineer.
- Photographs of the attic, the roof structure and the route from the front door to the attic.
- The access: how a beam gets in, for example through a gable window or the roof before it is felted.
What TopTac does
TopTac fabricates steel beams, plates and connections to the engineer's design in our workshop in Drogheda, certified to EN 1090 up to Execution Class 2, and can install them. We cut beams to length and can make them in bolted sections where access is tight, if the engineer approves the splice. See steel beams.
Sources and further reading
General information, not legal or engineering advice. Check with your engineer, architect or local authority.
Information checked against the official sources below in November 2026. Rules change, so check the current version.
- Department of Housing: Loft Conversion Guidelines (2022), gov.ie (PDF)
- Technical Guidance Document B Volume 2: Dwelling Houses (2017), gov.ie (PDF)
- Technical Guidance Document K (2014), gov.ie (PDF)
- Technical Guidance Document A: Structure (2012), gov.ie (PDF)
- Planning and Development Regulations 2001, S.I. No. 600 of 2001 (Irish Statute Book)
Converting an attic?
Send the engineer's drawings and a few photographs of the access.
Common questions
Is a converted attic a new storey?
How big does an escape rooflight need to be?
What headroom does a loft stair need?
Can TopTac size the beam for me?
Converting an attic?
Send the engineer's drawings and a few photographs of the access.
